NorabNorab - stop-it repair tape to repair pipes
line


MATERIALS HEALTH, SAFETY AND ENVIRONMENTAL SHEET

Preparation Date: 06/01/05

Product Name: FIX STIX™
For Information:
   Office:  (713)977-4100
   Fax:     (713)977-4164

Producer's Name: InduMar Products, Inc.
Address:  PO Box 770008
               Houston, TX 77215-0008
NFPA Placard Code


Section I. Product Identification and DOT Requirements

PRODUCT NAME

CHEMICAL FAMILY

CHEMICAL NAME

FORMULA

FIX STIX™

Epoxy & polymercaptan resins

Not applicable

Mixture


Section II. Hazard Information

100% INGREDIENTS

%

TOXICITY DATA

CAS NUMBER

2,4,6 - tri (dimethylaminomethyl) phenol
Epoxy resin (diglycidyl ether of bisphenol A)
Magnesium silicate
Mercaptan terminated polyether
Amorphous silica
Crystalline silica
Iron alloy

1
10
40
10
15
4
20

5 ppm 8 - hr. TWA
Oral LD50 (rbt)=
20 g/kg




90-72-2
25068-38-6
14807-96-6
Trade secret
67762-90-7
14808-60-7
Unknown

Known Hazards Under 29 CFR 1910.1200:


Combustible liquid
Flammable liquid
Pyrophoric material
Explosive material
Unstable material
Water reactive material
Oxidizer
Organic peroxide
Corrosive material
Compressed gas
Irritant (possible)
Skin hazard

YES










x

NO
x
x
x
x
x
x
x
x
x
x

x


Eye hazard
Toxic agent
Highly toxic agent
Sensitizer (possible)
Carcinogen
Reproductive toxin
Blood toxin
Nervous system toxin
Lung toxin
Liver toxin
Kidney toxin
Other

YES



x








NO
x
x
x

x
x
x
x
x
x
x

EPA Hazardous Waste ID No:      N/A                
EPA Hazard Waste Class:      
N/A


Section III. Physical Data


Boiling Point (°F): N/A
Vapor Pressure (MM Hg): N/A
Vapor Density (Air=1): N/A
Solubility in Water: Nil

Specific Gravity (Water=1): 1.9
PH: N/A
Evaporation Rate (BuAC=1): Nil
Volatile Components: N/A
Melting Point:  N/A
Appearance: Putty-like
Percent Volatile by Volume (%): Nil
Odor:  Mercaptan


Section IV. Emergency Response Data

Fire:  Extinguishing Media:    Water spray, foam, CO2 , dry chemicals
          Special Procedures:     None
          Unusual Hazards:        CO2 , aldehydes, acids, oxides of sulfur and nitrogen may be formed


Over-Exposure: Inhalation:        N/A
                              Ingestion:          Induce vomiting
                              Skin Contact:    Wash with soap and water
                              Eye Contact:     Flush with water - consult physician


Spills or Leaks: Dispose of in normal manner; not a potential pollutant.

 Waste disposal: Incinerate in furnace or bury in landfill according to applicable regulations.

Section V. Health and Hazard Data

Primary Routes of Entry:    Skin contact and eye contact
Effects of Over-Exposure:   Inhalation:   None
                                                   Ingestion:    N/A
                                                   Skin Contact:  Possible sensitizer
                                                   Eye Contact:   Possible sensitizer


Section VI. Special Protection Information

Protective Equipment Types:
Eyes:                Safety glasses
Respiratory:    None required
Gloves:            Polyethylene gloves for prolonged use
Other:               None required

Ventilation:
General Mechanical: None required
Local Exhaust:           Only if heated above 100°F (38°C)

Precautions:
Handling and Storage:  Avoid eye contact and excessive skin contact
Other:                               Wash with soap and water immediately after use


Section VII. Fire and Explosion Hazard Data

Flash Point:                 None
Flammable Limits:    LEL/UEL: Not applicable
Stability:                      Stable
Conditions to Avoid: None

Hazardous Polymerization: Will not occur
Conditions to Avoid:                     None
Hazardous Decomp Products:
   CO, aldehydes, acids, oxides of S and N


Section VIII. Special Precautions

No special handling procedures are necessary. Follow good industrial hygiene practices.
NOT FOR INTERNAL CONSUMPTION. KEEP AWAY FROM CHILDREN.

IMPORTANT NOTICE TO PURCHASER:
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof.


WARRANTIES:
The following is made in lieu of all warranties, expressed or implied. Seller's and Manufacturer's only obligationshall be to replace such quantity of the product proven to be defective. Neither Seller nor Manufacturer shall beliable for any injury, loss or damage, direct or consequential arising out of the use of or the inability to use the product. Before using, user shall determine the suitability of the product for its intended use and user assumes all risk and liability whatsoever in connection therewith. The foregoing may not be altered except by an agreement signed by officers of the Seller and the Manufacturer.


Legal responsibility is assumed only for the fact that all studies reported here and all opinions are those of qualified experts.

   
line